Products

 

Here at Custom Electronic Assemblies Company, we specialize in the design and production of your custom product. However, we also have several pre-designed products available. Please contact us to discuss your volume and timeline needs.

 

 

Custom Electronic Programmable Automatic Drain Valve: Model 5000

Our programmable automatic drain valve, the Model 5000 provides a positive solution to the problem of removing water and gunk from compressed air systems.


The straight-through full-port ball valve will readily handle gummy and oily fluids that can quickly foul solenoid valves and float operated drainers. The short cycle with high velocity flow keeps the connecting lines from clogging.


The solid state timing circuit includes a programmable module which controls the time interval between drain periods and length of the drain period. The design also provides a means of testing the timer as well as the motor drive when the operator presses an external test button.


The ball valves can be installed in a vertical or horizontal line, indoors or outdoors on any line or vessel that requires regular draining.  It requires 120V.


Available valve material choices of carbon steel, bronze, bronze with stainless steel trim, or all stainless steel, and in sizes of ½”, ¾” and 1”.

 

The Model 5000 is also available without the control board.

 

Custom Electronic Programmable Automatic Drain Valve: Model 5000 Custom Electronic Programmable Automatic Drain Valve: Model 5000

Available Options:
  • With or Without Control Board
  • Several Metal Types: Carbon Steel, Bronze, Bronze with Stainless, Steel Trim, Stainless Steel
  • Several Sizes: 1/2-inch, 3/4-inch, One-inch

Time Control Switch Settings
Switch No. Time Valve Closed Hour: Minutes
:15 :30 :45 1:00 1:15 1:30 1:45 2:00 2:15 2:30 2:45 3:00 3:15 3:30 3:45
1 ON   ON   ON   ON   ON   ON   ON   ON
2   ON ON     ON ON     ON ON     ON ON
3       ON ON ON ON         ON ON ON ON
4               ON ON ON ON ON ON ON ON
  Purge Time Seconds
4.5 9.0 13.5 18.0 22.5 27.0 31.5 36.0 40.5 45.0 49.5 54.0 58.5 63.0 67.5
5 ON   ON   ON   ON   ON   ON   ON   ON
6   ON ON     ON ON     ON ON     ON ON
7               ON ON ON ON ON ON ON ON
8       ON ON ON ON         ON ON ON ON


Three-Phase Line Monitor

Our three phase line monitor checks for missing phase and phase reversal. The unit will detect phase loss even on a running motor. The unit monitors 220 volt, 440 volt, and 600 volt phase-to-phase line voltages. The unit will operate on 50 or 60 Hertz. The unit has two sets of normally closed alarm contacts. One set for the missing phase alarm and one set fo the phase reveral alarm. The unit has two status lights. One indicates phase missing and one indicates phase reversal.

 

The unit requires a seperate 120 volt supply for its own operating voltage.

 




Heatless Regnerative Digital Air Dryer Controller

We offer a general purpose programmable heatless regenerative digital air dryer controller .

 

The unit can be purchased with or without an enclosure.

 

Features include:

  • 1 motherboard with euro-terminals, 5 heavy-duty triacs and 1 alarm relay
    • Outputs
      • Left Inlet
      • Right Inlet
      • Left Purge
      • Right Purge
      • Re-pressurization
      • Alarm Relay (dry contacts)
    • Inputs
      • Alarm Reset
      • Left Pressure Switch
      • Right Pressure Switch
      • Energy Saver - Extend cycle on low humidity (open contacts)
      • Humididty Alarm - Alarm on high humidity (closed contacts)
  • From the control panel you can easily set the six components of a desired cycle
    • Inlet Delay Time
    • Purge Delay Time
    • Purge Time
    • Re-pressurization Delay Time
    • Re-pressurization Time
    • Maximum Delay Time (before tower change over when dryer is working below design conditions. This delay can be placed under dewpoint control.)

 

Other Features

  • 2 Line by 16 Character LCD Display
  • 7 Status LEDs
  • 6 Touch Switches to program the unit and observe its status
  • Energy Saver Input
  • Operating records total operating hours
  • Records hours since last service
  • User selectable power-up mode
  • User selectable power-down mode
  • Fail-to-Switch Alarm
  • Humidity Alarm Input
  • The user can select load scheduling instead of dew point control

 

Heatless Regnerative Digital Air Dryer Controller Heatless Regnerative Digital Air Dryer Controller

Available Options:
  • With or Without Enclosure



Heated Digital Air Dryer Controller

We offer a general purpose programmable heated digital air dryer controller.

 

The unit can be purchased with or without an enclosure.

 

Features include:

  • User programmable cycle times
  • User programmable control temperature
  • User programmable limit temperature
  • EEprom for power down data retention
  • 32 character LCD display
  • Ability to display the time remaining in the current portion of the cycle, or any one of the four thermocouple temperatures on the LCD display
  • Open thermocouple alarm for each of the four thermocouples

 

Specifications:

  • Inputs
    • Four Type J thermocouple inputs
    • Two Press Switch inputs
    • One Humidity Switch input
  • Power Outputs
    • Tower 1 Select
      • Tower 2 Select
      • Tower 1 Heat
      • Tower 2 Heat
      • Purge
      • Alarm
  • Panel Switches
    • Alarm Reset
    • Step Advance
    • Mode Select
    • Enter
    • Up
    • Down
  • Display Lights
    • Alarm Reset
    • Tower 1
    • Tower 2
    • Heat
    • Purge
    • Cool
    • Re-pressurization
    • Set Mode
  • Character Display
    • 32 Character LCD Display
  • Power Down Backup
    • EEPROM
  • User Settings
    • Control Temp (75-1200 F)
    • Limit Temp (75-1200 F)
    • Heat Time (1 Min. - 99 Hrs.)
    • Cool Time (1 Min. - 99 Hrs.)
    • Re-pressurization Time (1 Min. - 99 Hrs.)

 

Available Options:
  • With or Without Enclosure



Vibratory Feeder Controller

The vibratory feeder controller controls the output level of the vibratory feeder by controlling the phase angle of the output drive.

 

Features include:

  • 0 to 2 second adjustable soft start
  • Controls AC or DC vibratory feeders
  • 4 to 20 mA tracking input or potentiometer to adjust level
  • Accepts to stop switch input
  • Minimum and maximum setpoint adjustments
  • Zero and span adjustments for the tracking input

 




Ultra-Air Field Replacement Parts

We sell replacement parts for the Ultra-Air Field Controller.

 

The unit can be purchased with or without an enclosure.

 

Ultra-Air Field Replacement Parts Ultra-Air Field Replacement Parts

Available Options:
  • With Enclosure, Part #: ELE-ED-85-CR
  • Board Assembly Only, Part#: ELE-TB-85-CE